FirstCheck
EN FR
🍁 Conçu pour les foyers canadiens — rédigé selon les codes canadiens et les règles provinciales. N’est pas destiné à un usage hors du Canada.
ÉBAUCHE — cette page n’a pas encore été révisée par un professionnel licencié. Aperçu éditorial seulement.

Washing machine is leaking water

A puddle by the washer is alarming, but the leak is usually from a loose hose you can reach and tighten — not the guts of the machine. The first job is just finding where the water is coming from.

tuneQue remarquez-vous?
Sélectionnez ce qui correspond et la liste ci-dessous se réordonne. Pas certain? Passez.
emergency_home

flag
Commencez ici

In Canadian homes, look behind the machine first. Pull it out gently and feel the two hose connections at the taps and at the machine — a loose coupling or a wet, cracked, or bulging hose is the most common leak by far. Hand-tighten a loose fitting; if a hose is old rubber, plan to replace both with braided steel. Know where the hot and cold shutoff valves are before you start.

Classé selon des données de pannes réelles. L’ordre s’ajuste selon vos observations ci-dessus.

Causes probables, dans l’ordre à vérifier

Ordre typique affiché
Pour débutant Faisable, avec soin Sécurité critique Appelez un pro

visibilityHow to check

  1. Locate the hot and cold shutoff valves on the wall behind the machine so you can stop the water in seconds if you need to.
  2. Dry everything with a towel, then run a short cycle and watch the four hose connections — two at the wall taps, two at the machine — for beads of water forming.
  3. Feel each hose along its length: soft, bulging, or cracked rubber is failing. A wet coupling that a gentle hand-tighten stops was simply loose; one that keeps weeping needs a new rubber washer or a new hose.
buildflashlightbuildtowel schedule10 min

handymanHow to fix it

warning Stop the water and mind the outletIf the machine is actively leaking, close the hot and cold supply valves behind it first — that stops the water at the source. Keep the puddle away from the wall outlet the washer plugs into; if water has already reached it, unplug at the breaker, not by yanking a wet cord, and don't stand in the water. Only work on the hoses once the area is dry and the valves are shut.

Shut off the hot and cold supply valves, unthread the old hoses, and fit fresh braided stainless-steel hoses with new rubber washers — hand-tight plus a gentle quarter-turn — then reopen the valves and watch every connection for leaks before pushing the machine back.

  1. Close both shutoff valves behind the machine (handle crosswise to the pipe), then unthread the hoses from the taps and the machine — keep a towel handy, a little water will spill.
  2. Check that each connection has an intact rubber washer seated inside; fit fresh braided stainless-steel hoses, matching hot to hot and cold to cold.
  3. Thread each fitting on by hand until snug, then a gentle quarter-turn with pliers — do not overtighten, it crushes the washer and makes leaks worse.
  4. Reopen the valves slowly and watch all four connections for a full minute. A dry set of joints means you're done; any bead means shut off and reseat that fitting.
schedule20 min savings$10–40
Braided stainless-steel washing machine fill hoses (pair)Match the thread (usually 3/4" garden-hose thread) and pick a length that reaches with slack; buy them in a hot/cold pair
gavel Vérifiez d’abord votre province AB: permis au propriétaire · BC: permis au propriétaire · ON: permis au propriétaire · PE: permis au propriétaire · QC: permis au propriétaire
Replacing washing-machine fill hoses is routine homeowner maintenance in every province.

handymanHow to fix it

Run smaller loads, switch to HE detergent if your machine is high-efficiency, and use only the small dose the label calls for — the leak that comes with foam is usually a dosing habit, not a broken part.

  1. Don't pack the drum — clothes should tumble with a hand's width of space at the top.
  2. If your machine is high-efficiency (an HE logo on the front or drawer), use only HE detergent; regular soap oversuds badly in these machines.
  3. Measure to the low line on the cap or a single pod, not by eye — more soap does not mean cleaner clothes, just more foam. Run a short load and confirm the suds no longer push water out.
schedule10 min savings$0–20
gavel Vérifiez d’abord votre province AB: permis au propriétaire · BC: permis au propriétaire · ON: permis au propriétaire · PE: permis au propriétaire · QC: permis au propriétaire
Adjusting load size and detergent is not regulated work — homeowner-allowed everywhere.

visibilityHow to check

  1. Find the standpipe the washer's drain hose empties into and watch it during the drain and spin, when the machine pumps water out fastest.
  2. If water rises up the standpipe and spills over the top — rather than leaking from the machine itself — the pipe or the drain line beyond it is partly clogged.
  3. Clearing lint and soap gunk from the top of the standpipe may restore flow. If it backs up again, or the clog is deeper than you can reach, that's drain plumbing for a licensed plumber.
buildflashlight schedule10 min
warning Unplug before you work at the door sealBefore peeling back or replacing a front-loader door boot, unplug the machine and close the supply valves — you'll have your hands inside near the door lock and drum. Replacing a boot is fiddly and model-specific; if the retaining spring or the tub side of the seal is involved, it's a fair job to hand to an appliance technician rather than force.

verifiedPourquoi confier ceci à un pro

Reaching a cracked internal hose, the drain pump, or a worn tub seal means pulling the cabinet apart around live 120 V wiring and a heavy tub. This is an appliance technician's repair — they can confirm the source and quote it quickly, and the part is usually small next to the cost of a water-and-electricity mistake.

Vos notes accompagnent la demande — ce que vous avez vu, ce que vous avez éliminé, quand ça a commencé — pour que le pro arrive avec une longueur d’avance.

sort

Pourquoi la liste est dans cet ordre

Nous ne classons pas seulement selon la probabilité. Nous classons comme le ferait un bon artisan honnête : éliminer d’abord les causes gratuites, sûres et courantes. C’est pourquoi les vérifications peu coûteuses passent avant les réparations chères — et pourquoi tout ce qui est dangereux reçoit un arrêt net plutôt qu’un encouragement. Cet ordre existe pour vous faire économiser, pas pour vous vendre quelque chose.