FirstCheck
EN FR
🍁 Conçu pour les foyers canadiens — rédigé selon les codes canadiens et les règles provinciales. N’est pas destiné à un usage hors du Canada.
ÉBAUCHE — cette page n’a pas encore été révisée par un professionnel licencié. Aperçu éditorial seulement.

In-floor heating: a zone won't warm up

A single cold zone is usually something small and local — a setback on the thermostat, a tripped GFCI, or a pocket of air in one loop — not the whole floor system failing.

tuneQue remarquez-vous?
Sélectionnez ce qui correspond et la liste ci-dessous se réordonne. Pas certain? Passez.
emergency_home

flag
Commencez ici

In Canadian homes, check the thermostat first. Turn it well up, make sure it isn't in a programmed setback, and confirm the floor-sensor mode is selected. On an electric floor, look for a tripped GFCI or test button on the thermostat and reset it once — a bumped setting or a single GFCI trip is the most common reason a zone goes cold, and it costs nothing to rule out. If the GFCI won't stay reset, stop and read the safety note.

Classé selon des données de pannes réelles. L’ordre s’ajuste selon vos observations ci-dessus.

Causes probables, dans l’ordre à vérifier

Ordre typique affiché
Pour débutant Faisable, avec soin Sécurité critique Appelez un pro

visibilityHow to check the settings and GFCI

report A GFCI that won't reset is telling you somethingThe GFCI on an electric floor protects against a live-to-ground fault in a cable buried under the floor. Resetting it once is fine. If it trips again the moment you reset it, stop — the fault is real and forcing power to it risks shock and damage. This is not a homeowner repair; leave the circuit off and call a licensed electrician to locate the fault.
  1. Turn the thermostat well above room temperature and check it isn't in a programmed setback or vacation mode; confirm it's set to sense the floor (floor or floor+air), not air only.
  2. On an electric floor, look for a GFCI or a small test/reset button on the thermostat. If it has tripped, press reset once and watch it.
  3. If the GFCI holds and the floor warms within 20–30 minutes, you're done. If it trips again immediately, do not keep resetting it — that's a ground fault, and it routes to an electrician.
buildAucun outil schedule10 min

visibilityHow to check

  1. With the system running and calling for heat, feel the supply and return pipes for the cold loop at the manifold — a loop full of air stays cool while its neighbours warm up.
  2. Listen at the manifold: gurgling or trickling water sounds point to trapped air rather than a closed valve.
  3. Confirm the zone valve for that loop is actually open before blaming air — a stuck valve looks the same from a distance (see the zone-valve cause).
buildflashlight schedule15 min

handymanHow to fix it

Bleed or purge the affected loop at the manifold: with the boiler off and the system cool enough to handle, open the loop's purge/drain and feed valves to push the trapped air out with water flow, then re-check system pressure and top up if needed.

  1. Turn the boiler off and let the loops cool to a safe temperature before touching valves — hydronic water can be scalding.
  2. Isolate the affected loop at the manifold (close the other loops) so incoming water is forced through the airbound one.
  3. Open that loop's purge/drain to a bucket or hose and open the fill valve; run water through until it flows clear with no sputtering air, then close up.
  4. Restore the other loops, check the boiler pressure gauge against the normal range on the label, top up if low, and confirm the zone warms. If pressure won't hold, that's a separate boiler-side problem for a pro.
schedule40 min savings$0–15
gavel Vérifiez d’abord votre province AB: permis au propriétaire · BC: permis au propriétaire · ON: permis au propriétaire · PE: permis au propriétaire · QC: permis au propriétaire
Bleeding or purging a hydronic loop and adjusting the thermostat are generally owner-permitted maintenance; boiler-side repairs remain licensed work.

verifiedPourquoi confier ceci à un pro

A heating cable set in mortar or slab can't be diagnosed or repaired from the surface, and a ground fault in it is why the GFCI keeps tripping. Locating the break takes specialized tracing tools, and the repair must follow the cable maker's method to stay safe and warranted. Leave the circuit off and bring in a licensed electrician.

gavel Vérifiez d’abord votre province AB: réservé aux licenciés · BC: réservé aux licenciés · ON: permis et inspection requis · PE: réservé aux licenciés · QC: réservé aux licenciés
Locating and repairing a buried heating cable is licensed electrician work in most provinces; confirm the provincial rule before publishing.

Vos notes accompagnent la demande — ce que vous avez vu, ce que vous avez éliminé, quand ça a commencé — pour que le pro arrive avec une longueur d’avance.

verifiedPourquoi confier ceci à un pro

Reading the boiler's pressure gauge is fine. Beyond that, restoring pressure, bleeding the boiler, or replacing a circulator means working on a closed, pressurized heating system — get it wrong and you can flood a floor, damage the boiler, or scald yourself. Have a licensed HVAC/hydronic technician diagnose and repair the boiler side.

Vos notes accompagnent la demande — ce que vous avez vu, ce que vous avez éliminé, quand ça a commencé — pour que le pro arrive avec une longueur d’avance.

sort

Pourquoi la liste est dans cet ordre

Nous ne classons pas seulement selon la probabilité. Nous classons comme le ferait un bon artisan honnête : éliminer d’abord les causes gratuites, sûres et courantes. C’est pourquoi les vérifications peu coûteuses passent avant les réparations chères — et pourquoi tout ce qui est dangereux reçoit un arrêt net plutôt qu’un encouragement. Cet ordre existe pour vous faire économiser, pas pour vous vendre quelque chose.