FirstCheck
EN FR
🍁 Conçu pour les foyers canadiens — rédigé selon le Code canadien de l’électricité et les règles provinciales. N’est pas destiné à un usage hors du Canada.
ÉBAUCHE — cette page n’a pas encore été révisée par un professionnel licencié. Aperçu éditorial seulement.

A light switch is warm or buzzing

A dimmer that feels a little warm under a big light load is usually normal — but a switch that's too hot to touch, discoloured, or smells hot is worth taking seriously, and this page will help you tell which one you have.

tuneQue remarquez-vous?
Sélectionnez ce qui correspond et la liste ci-dessous se réordonne. Pas certain? Passez.
emergency_home

flag
Commencez ici

In Canada, if the switch buzzes or the lights flicker, the usual cause is a dimmer paired with the wrong bulbs — non-dimmable LEDs, or more LED bulbs than the dimmer is rated for. Look at the bulb boxes for the word "dimmable" and count how many you're running. Swapping to dimmable LEDs, or to a dimmer made for LED loads, usually clears the buzz. This is a compatibility issue, not a wiring fault.

Classé selon des données de pannes réelles. L’ordre s’ajuste selon vos observations ci-dessus.

Causes probables, dans l’ordre à vérifier

Ordre typique affiché
Pour débutant Faisable, avec soin Sécurité critique Appelez un pro

handymanHow to fix it

Swap the bulbs for dimmable LEDs (or, if they already are, reduce the count or fit an LED-rated dimmer) so the dimmer and its load are matched. Changing bulbs is no-tools homeowner work; changing the dimmer is a separate switch-replacement job.

  1. Check the bulb boxes for the word "dimmable." Non-dimmable LEDs on a dimmer commonly buzz or flicker and should be replaced with dimmable ones.
  2. If the bulbs are already dimmable, count them and compare against the dimmer's LED rating — dimmers list a much lower LED wattage or a maximum bulb count. Too many bulbs is a common cause of hum.
  3. If a matched set of dimmable LEDs still buzzes, fit a dimmer specifically rated for LED loads. Replacing the dimmer is a switch-swap — do it with the power off and read the switch-replacement gate first.
schedule10 min savings$5–60

visibilityHow to check

  1. Read the wattage rating printed on the dimmer (often on the mounting strap or in the paper insert) — for example "600 W incandescent".
  2. Add up the wattage of every bulb the dimmer controls. Incandescent and halogen bulbs count at their full listed watts; LED bulbs draw far less but have their own, lower dimmer limits.
  3. If the total is within the rating and the dimmer is only mildly warm — comfortable to keep a finger on, no discolouration, no smell — this is normal. If it's hot to the touch, discoloured, or smells hot, treat it as a connection problem, not a loaded dimmer.
buildAucun outil schedule5 min

handymanHow to fix it

report Kill the breaker and prove it's dead firstA switch replacement is doable with care, but the wires behind it are live until you shut off the right breaker — and a warm switch is exactly the situation where a bad connection can bite. Turn off the breaker, then confirm the switch is dead with a non-contact voltage tester before you touch a wire. If the plate is discoloured or scorched, don't treat this as a simple swap: something overheated, and a licensed electrician should find out why before a new switch goes in.

Turn off the breaker, confirm the switch is dead, then replace it like-for-like — same type and rating — noting how each wire was connected and re-terminating on the screw terminals, not the push-in backstab holes.

  1. Switch off the breaker feeding the circuit, then confirm the switch is truly dead with a non-contact voltage tester before touching any wire.
  2. Remove the plate and the two mounting screws, ease the switch out, and photograph or label how each wire is connected before you loosen anything.
  3. Fit a new switch of the same type and rating. Wrap each wire clockwise under its screw terminal and tighten firmly — do not reuse the push-in backstab holes, which are a common cause of the loose, overheating connection you're trying to avoid.
  4. Tuck the wires back neatly, mount the switch, restore power, and check that it operates cleanly with no buzz, warmth, or flicker.
schedule30 min savings$5–25
Replacement light switch or dimmerMatch the type (single-pole, 3-way, dimmer) and current rating stamped on the old one
gavel Vérifiez d’abord votre province AB: permis au propriétaire · BC: permis au propriétaire · ON: permis et inspection requis · PE: permis au propriétaire · QC: réservé aux licenciés
Like-for-like replacement of a switch or dimmer with the power off is generally permitted homeowner work; confirm the local rule before publishing.

verifiedPourquoi confier ceci à un pro

A loose or backstabbed connection that's overheating has already been running hot behind the plate — the fix isn't just tightening a screw, it's finding out why it loosened and whether the wire or terminal is damaged. Cut the breaker, stop using the switch, and have a licensed electrician diagnose it. Under the Canadian Electrical Code this is exactly the kind of connection work that must be done right, and the cost of getting it wrong is a fire.

Vos notes accompagnent la demande — ce que vous avez vu, ce que vous avez éliminé, quand ça a commencé — pour que le pro arrive avec une longueur d’avance.

warning Right-sizing a switch is more than swapping itIf a switch is warm because it's carrying more load than it's rated for, fitting a bigger switch is not the whole answer — the wire and breaker have to match the load too, or you move the overheating somewhere less visible. Have a licensed electrician confirm the circuit is sized correctly rather than guessing.
sort

Pourquoi la liste est dans cet ordre

Nous ne classons pas seulement selon la probabilité. Nous classons comme le ferait un bon artisan honnête : éliminer d’abord les causes gratuites, sûres et courantes. C’est pourquoi les vérifications peu coûteuses passent avant les réparations chères — et pourquoi tout ce qui est dangereux reçoit un arrêt net plutôt qu’un encouragement. Cet ordre existe pour vous faire économiser, pas pour vous vendre quelque chose.