FirstCheck
EN FR
🍁 Conçu pour les foyers canadiens — rédigé selon les codes canadiens et les règles provinciales. N’est pas destiné à un usage hors du Canada.
ÉBAUCHE — cette page n’a pas encore été révisée par un professionnel licencié. Aperçu éditorial seulement.

Garage door closes partway then reverses

This is usually the door's safety system working, not a breakdown — most of the time a five-minute wipe and nudge of the little sensors near the floor sets it right.

tuneQue remarquez-vous?
Sélectionnez ce qui correspond et la liste ci-dessous se réordonne. Pas certain? Passez.
emergency_home

flag
Commencez ici

In Canada, start at the two safety sensors near the floor, one on each track. Wipe each lens clean with a soft cloth, clear anything breaking the beam, and gently nudge them until both indicator lights glow steady (not blinking). This is the most common fix by far, it's free, and it takes about five minutes. A steady light on both eyes means the beam is aligned.

Classé selon des données de pannes réelles. L’ordre s’ajuste selon vos observations ci-dessus.

Causes probables, dans l’ordre à vérifier

Ordre typique affiché
Pour débutant Faisable, avec soin Sécurité critique Appelez un pro

visibilityHow to check

  1. Find the two small sensors mounted near the floor on each track — one usually shows a steady light (the sender), the other a light that goes out or blinks when the beam is broken (the receiver).
  2. Wipe each lens gently with a soft, dry cloth, and clear anything sitting in the beam's path — a bin, a bike wheel, a coil of hose, even a thick cobweb.
  3. Watch the lights: if one is off or blinking, loosen its wing-nut or bracket slightly and tilt the sensor until both lights glow steady, then re-snug it. Try closing the door again from the wall button.
buildAucun outil schedule10 min

handymanHow to fix it

Wipe both sensor lenses clean, clear the beam path, and gently realign the sensors until both indicator lights are steady, then re-tighten the brackets and test the door.

  1. Clear the doorway of anything that could break the beam, then wipe both sensor lenses with a soft, dry cloth — dust and condensation film are common culprits in a Canadian garage.
  2. If a light is still off or blinking, loosen the bracket wing-nut and slowly tilt that sensor up, down, and side to side until its light glows steady and matches the other.
  3. Re-tighten the bracket without knocking the aim off, then close the door from the wall button and watch it seat fully to the floor without reversing.
  4. If both lights are steady and clean but the door still reverses at the floor, the photo-eyes aren't the cause — move on to the opener's close-force setting.
schedule10 min savingssouvent gratuit
gavel Vérifiez d’abord votre province AB: permis au propriétaire · BC: permis au propriétaire · ON: permis au propriétaire · PE: permis au propriétaire · QC: permis au propriétaire
Cleaning and aligning the safety photo-eyes is routine homeowner maintenance in every province and is not trade-licensed. Adjusting the opener's close-force limit is likewise owner-permitted, but must preserve the auto-reverse. Torsion-spring and cable work is not DIY on safety grounds regardless of province — route it to a garage-door professional.

visibilityHow to check

  1. Confirm the photo-eyes are clean and aligned first — a force problem and a sensor problem look identical from across the garage.
  2. Watch the door reverse: if it touches the floor (or nearly) and then backs off, the down-force or down-limit is likely too sensitive; if it reverses in mid-travel, look at the tracks instead.
  3. Find the force and travel-limit adjustments on the opener head (dials, screws, or buttons — see your manual) and note the current settings before touching anything.
buildAucun outil schedule15 min

verifiedPourquoi confier ceci à un pro

The torsion spring above the door is wound to hold the door's full weight and stores enough energy to break bones or worse if it lets go while you're near it — this is one of the most common serious garage injuries. Adjusting or replacing it needs winding bars and training. Don't loosen it, don't try to 'help' it, and don't run the opener against a broken one. A garage-door professional replaces springs quickly and safely, usually in a single visit.

Vos notes accompagnent la demande — ce que vous avez vu, ce que vous avez éliminé, quand ça a commencé — pour que le pro arrive avec une longueur d’avance.

verifiedPourquoi confier ceci à un pro

Straightening a bent track or replacing a door section means working around the door's counterbalance springs and cables while the panel is partly supported. Get it wrong and the door can bind, fall, or release stored spring tension. A garage-door pro has the tools and can realign the track or swap a section safely.

Vos notes accompagnent la demande — ce que vous avez vu, ce que vous avez éliminé, quand ça a commencé — pour que le pro arrive avec une longueur d’avance.

sort

Pourquoi la liste est dans cet ordre

Nous ne classons pas seulement selon la probabilité. Nous classons comme le ferait un bon artisan honnête : éliminer d’abord les causes gratuites, sûres et courantes. C’est pourquoi les vérifications peu coûteuses passent avant les réparations chères — et pourquoi tout ce qui est dangereux reçoit un arrêt net plutôt qu’un encouragement. Cet ordre existe pour vous faire économiser, pas pour vous vendre quelque chose.