FirstCheck
EN FR
🍁 Conçu pour les foyers canadiens — rédigé selon les codes canadiens et les règles provinciales. N’est pas destiné à un usage hors du Canada.
ÉBAUCHE — cette page n’a pas encore été révisée par un professionnel licencié. Aperçu éditorial seulement.

Electric baseboard heater won't shut off

A heater that won't quit is unsettling, but it's usually one failed part — most often the thermostat — and you can stop it safely right now by switching off its breaker.

tuneQue remarquez-vous?
Sélectionnez ce qui correspond et la liste ci-dessous se réordonne. Pas certain? Passez.
emergency_home

flag
Commencez ici

In Canada, the most common cause to rule out is a thermostat whose contacts have welded shut. Turn the dial or thermostat all the way down; if the heater keeps running full blast, the switch is no longer cutting power. It costs nothing to check, and you can stop the heater right now by switching off its breaker — but the repair is a live 240-volt thermostat swap, so read the safety note first.

Classé selon des données de pannes réelles. L’ordre s’ajuste selon vos observations ci-dessus.

Causes probables, dans l’ordre à vérifier

Ordre typique affiché
Pour débutant Faisable, avec soin Sécurité critique Appelez un pro

visibilityHow to check

report This is a live 240-volt circuitBaseboard thermostats switch the full 240 volts, and both wires stay live even with the dial turned "off" — only the breaker truly de-energizes the heater. Kill the breaker before you open the thermostat and verify it's dead. If testing a live circuit isn't something you're set up to do safely, stop here: this is a fast, inexpensive job for a licensed electrician.
  1. With power still on, turn the dial or thermostat fully down (or to "off"). If the heater keeps running full blast, the switch is not opening — that alone is a strong sign the contacts are welded.
  2. Switch OFF the breaker for that circuit, verify the heater is dead with a voltage tester, then remove the thermostat cover — a line-voltage thermostat carries the full 240 volts.
  3. With power off, inspect the contacts for pitting or fused metal, and check continuity across the switch: a thermostat that reads closed (continuous) even in its "off" position has welded contacts and must be replaced.
buildmultimeterbuildscrewdriver schedule20 min

handymanHow to fix it

Stop it now — go to the electrical panel and switch off the breaker for that circuit so the heater stops drawing power, then keep drapes, furniture, and bedding well clear until it's repaired.

  1. At the electrical panel, find the breaker for that room's baseboard circuit — it may be labelled by room, or trace it by which breaker stops the heater.
  2. Switch it fully OFF. Confirm the heater has stopped and is cooling down.
  3. Pull drapes, furniture, and bedding well clear of the heater, and leave the breaker off until the thermostat or wiring is repaired.
schedule5 min savingssouvent gratuit
gavel Vérifiez d’abord votre province AB: permis au propriétaire · BC: permis au propriétaire · ON: permis au propriétaire · PE: permis au propriétaire · QC: permis au propriétaire · AB: permis au propriétaire · BC: permis au propriétaire · ON: permis et inspection requis · PE: permis au propriétaire · QC: réservé aux licenciés
Switching a circuit off at your own panel is not electrical work — it's routine and permitted for any homeowner in every province.

handymanHow to fix it

On the thermostat screen, cancel any "Hold" or "Vacation" override and lower or reset the schedule so it stops calling for heat; if it's badly mis-programmed, do a factory reset and re-enter a sensible schedule.

  1. Look for a "Hold," "Permanent Hold," or "Vacation" indicator on the display and cancel it so the thermostat returns to its schedule.
  2. Lower the current setpoint below room temperature and confirm the heater switches off within a minute or two.
  3. Review the programmed schedule for a stuck-high period; if it's tangled, reset the thermostat to defaults and re-enter a simple schedule.
schedule10 min savingssouvent gratuit

verifiedPourquoi confier ceci à un pro

If 240-volt line power is reaching the heater without passing through the thermostat, a wire has been mis-connected or has failed. Repairing it safely means finding why the thermostat is being bypassed, not just re-landing a wire. Leave the circuit off and have a licensed electrician trace and repair it.

Vos notes accompagnent la demande — ce que vous avez vu, ce que vous avez éliminé, quand ça a commencé — pour que le pro arrive avec une longueur d’avance.

warning If the wiring isn't clearly labelled, hand this to an electricianWorking out which thermostat controls which heater means opening 240-volt junctions with the breaker off and verified dead. If the wiring is unlabelled, shared between rooms, or you're unsure what feeds what, don't guess — a licensed electrician can map and correct it quickly and safely.
sort

Pourquoi la liste est dans cet ordre

Nous ne classons pas seulement selon la probabilité. Nous classons comme le ferait un bon artisan honnête : éliminer d’abord les causes gratuites, sûres et courantes. C’est pourquoi les vérifications peu coûteuses passent avant les réparations chères — et pourquoi tout ce qui est dangereux reçoit un arrêt net plutôt qu’un encouragement. Cet ordre existe pour vous faire économiser, pas pour vous vendre quelque chose.